Water Right Impression Series Guida alla Risoluzione dei Problemi

Navigare online o scaricare Guida alla Risoluzione dei Problemi per Dispenser per l’acqua Water Right Impression Series. Water Right Impression Series Troubleshooting guide Manuale Utente

  • Scaricare
  • Aggiungi ai miei manuali
  • Stampa

Sommario

Pagina 1 - Impression Plus Series

Impression Series®andImpression Plus Series®Metered Water Softeners

Pagina 2 - TABLE OF CONTENTS

105. ERROR MESSAGE: If the word “ERROR” and a number arealternately flashing on the display record the number and contactthe dealer for help. This ind

Pagina 3 - BYPASS VALVE:

START-UP INSTRUCTIONS:• After installation is complete, rotate bypass handles to bypass mode (see Fig.2 on page 4).• Turn on water and check for leaks

Pagina 4

12TROUBLESHOOTING GUIDE:PROBLEM CAUSE CORRECTION 1. No display on PC boardA. No power at electric outlet A. Repair outlet or use working outletB. Cont

Pagina 5 - INSTALLATION:

137. Control valve does notregenerate automaticallybut does when thecorrect button(s) isdepressed and held. Fortimeclock valves thebuttons are ▲ &

Pagina 6

12. Control valve fails todraw in regenerantA. Injector is plugged A. Remove injector and clean or replaceB. Faulty regenerant piston B. Replace regen

Pagina 7 - PROGRAMMING PROCEDURES:

16. E3, Err – 1003, Err –103 = Control valvemotor ran too long andwas unable to find thenext cycle positionA. Motor failure during a regenerationA. Ch

Pagina 8

16REPLACEMENT PARTS:2713546FRONT COVER AND DRIVE ASSEMBLYItem No. Part No. Description Qty.1CV3540-A Black Impression®cover 1CV3540-W-A Gray Impressio

Pagina 9 - BATTERY REPLACEMENT

6810117 97 12423511314NOTE: For Impression Plus® Models only. Not available on 1¼ " valve.17REPLACEMENT PARTS:For Impression Plus®Models OnlyPI

Pagina 10

18REPLACEMENT PARTS:BYPASS VALVEItem No. Part No. Description Qty.1 CV3151 Nut, 1" quick connect 22 CV3150 Split ring 23 CV3105 O-ring 215 24 CV3

Pagina 11 - START-UP INSTRUCTIONS:

19INJECTOR ASSEMBLIESItem No. Part No. Description Qty.1CV3176 Injector cap 12CV3152 O-ring 135 13CV3177-01 Injector screen 14CV3010-1Z Injector assem

Pagina 12 - TROUBLESHOOTING GUIDE:

TABLE OF CONTENTSPreinstallation Instructions for Dealers . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Bypass Valve . . . . . . . . . . .

Pagina 13 - PROBLEM CAUSE CORRECTION

20REPLACEMENT PARTS:DRAIN LINE ASSEMBLY 3/4"Item No. Part No. Description Qty.1 CH4615 Elbow locking clip 12 CPKP10TS8-BULK Optional insert, 5/8&

Pagina 14 - TROUBLESHOOTING GUIDE cont’d:

21WATER METER & METER PLUGItem No. Part No. Description Qty.1 CV3151 Nut, 1" QC 12 CV3003 Meter assembly, includes items 3 & 4 13 CV3118-

Pagina 15

22REPLACEMENT PARTS:2345678101911BRINE TANK ASSEMBLYItem No. Part No. Description Qty.1CG2191- 84 Brine tank cover, injection molded WR 1CG2180 Brine

Pagina 16 - REPLACEMENT PARTS:

23REPLACEMENT PARTS:132See opposite page for safety float system parts.CABINET BRINE TANK ASSEMBLYItem No. Part No. Description Qty.1 CG2197-01 Salt a

Pagina 17

241" PVC MALE NPT ELBOWItem No.Part No. Description Qty.CV3007 1" PVC male NPT elbow assembly 21 CV3151 Nut, 1" quick connect 22 CV3150

Pagina 18

251-1/4" & 1-1/2" PVC SOLVENTItem No.Part No. Description Qty.CV3007-07 1-1/4" & 1-1/2" PVC solvent assembly 21 CV3151 Nut

Pagina 19

26IM-844 IM-1044 IM-1054 IM-1354 IM-1465IM-1465-IM-1665IM-1665-IMC-835 IMC-1035MODEL 1.25" 1.25"1Capacity: Maximum 25,600 @ 9.0 32,000 @ 1

Pagina 20

27Water Conditioner Limited WarrantyCongratulations. You have purchased one of the finest water treatment systems available. In the unlikelyevent of a

Pagina 21

1900 Prospect Court • Appleton, WI 54914Phone: 920-739-9401 • Fax: 920-739-9406MANUAL REGENERATIONNOTE: For softeners,if brine tank does notcontai

Pagina 22

PREINSTALLATION INSTRUCTIONS FOR DEALERS:BYPASS VALVE:3The manufacturer has preset the water treatment unit’s sequence of cycles, cycle times, salt do

Pagina 23

41. NORMAL OPERATION POSITION: The inlet and outlet handles point in the direction of flowindicated by the engraved arrows on the control valve. Wate

Pagina 24

5GENERAL INSTALLATION & SERVICE WARNINGSThe control valve, fittings and/or bypass are designed to accommodate minor plumbing misalignments. There

Pagina 25 - 1" BRASS SHARK BITE

66. INLET/OUTLET PLUMBING: Be sure to install Bypass Valve onto main control valve before beginningplumbing. Make provisions to bypass outside hydran

Pagina 26 - SPECIFICATIONS:

7Time of day should only need to be set after extended power outages or when daylight saving time beginsor ends. If an extended power outage occurs, t

Pagina 27

8STEP 4 – REGENERATION HOUR: The manufacturer has factory set 2:00 A.M. as the default. Thisis the hour of day for regeneration and can be reset by us

Pagina 28 - QUICK REFERENCE GUIDE:

3. MANUAL REGENERATION: Sometimes there is a need toregenerate before the control valve calls for it. This may beneeded if a period of heavy water use

Commenti su questo manuale

Nessun commento